All syllabi
BCSWritten
BCS written syllabus
General and technical cadres · 235 pages
Compulsory subjects and post-related subjects for professional and technical cadres. Confirm the applicable subject code in the recruitment notice.
Published by BPSC. Collected 2026-11-14. Confirm the edition and subject against your recruitment notice before studying.
Text below is extracted for search and may contain mistakes. Use the original PDF to check marks, formulas and Bangla spelling.
BanglaEnglishBangladesh affairsInternational affairsCivil engineeringElectrical engineeringMechanical engineeringComputer science
Read the document
Page 217 of 235
Searchable text (unverified)
SYLLABUS FOR BCS (WRITTEN) EXAMINATION
217/235
(PSK)- Principle, Bandwidth Requirements, Detection, Differential PSK, Quadrature PSK,
Noise Performance, Frequency -Shift Keying (FS K)- Principle, Continuous and
Discontinuous Phase FSK, Minimum -Shift Keying (MSK), GMSK, Bandwidth
Requirements, Detection of FSK, Multilevel Signalling, M -Ary Modulation Techniques,
Spread Spectrum Modulation Techniques, DSSS, FHSS.
Multiplexing: Time-Division Multiplexing (TDM), Receiver Synchronization, Frame
Synchronization, TDM of Multiple Bit Rate Systems, Frequency -Division Multiplexing
(FDM) Principle, Demultiplexing; Wavelength -Division Multiplexing, Multiple -Access
Network- Time-Division Multiple-Access (TDMA), Frequency -Division Multiple Access
(FDMA), Code -Division Multiple -Access (CDMA) Spread Spectrum Multiplexing,
Coding Techniques and Constraints of CDMA.
3. Microprocessor and Interfacing
Introduction to Microprocessor : Classification and Ev olution of Microprocessor,
Difference between Microprocessor and Microcontroller.
8086 Microprocessor: Basic Architecture, Registers, Flags, Real Mode Operation of 8086
Microprocessor, Segment, Offset and Physical Address, Instruction Format, Functions of
Different Instructions of 8086 Microprocessor, Pins and Signals, Bus Buffering and
Latching, Bus Timing, Ready and Wait State Generation, Clock Generator (8284A),
Memory Segmentation.
Interrupts: Introduction to Interrupts, Interrupt Vector Table, Interrup t Instructions and
Operation, Hardware and Software Interrupts, Interrupt Driven I/O, Programmable
Interrupt Controller (8259A).
Microprocessor Programming : Introduction to Assembly Language Programming
(ALP), Macro and Procedure, Writing Simple ALPs using Different I/O Functions, Macro,
Procedures.
Memory: Memory Types, Memory Banks, Memory Read -Write Cycle, Memory
Interfacing.
I/O Interfacing : I/O Instructions, Basic I/O Interfacing, I/O Port Address Decoding,
Programmable Peripheral Interface (8255A IC), Peripheral Interfacing Examples,
Programmable Interval Timer (8254), Timer Interfacing, D/A and A/D Converter,
Programmable Communication Interface, Interfacing Serial I/O Devices.
DMA: Basic DMA Operation, DMA Controller, DMA Processed Interface.
4. Control Systems
Introduction: Introduction to Control Systems, Definitions and classification
Solution of Differential Equations : Standard Inputs to Control Systems, SteadyState
Response and Transient Response.
System Representation : Block Diagrams, Determin ation of the Overall Transfer
Function, Signal Flow Graphs.
Control System Characteristics : Routh -Hurwitz Stability Criterion, Feedback System
Types, Analysis of System, Types, Steady -Mate Error Coefficients, Non Unity -Feedback
System.
Root Locus: Plotting Roots of a Characteristics Equation, Qualitative Analysis of the Root
Locus, Open -Loop Transfer Function, Poles of the Control Ratio, Applications of the
Magnitude and Angle Condition.
Root Locus Compensation Design: Introduction to Design, Transient Response Dominant
Complex Poles, Additional Significant Poles, Ideal Integral Cascade Compensation (PI
Controller), PID controller, Ideal Derivative Cascade Compensation (FD Controller), FID
Controller, Introduction to Feedback Compensation.