Skip to content
Search jobs inside ChatGPT or Claude. Claude, ChatGPT, Claude Code, Codex, Gemini, Cursor and Grok
Connect
All syllabi
BCSWritten

BCS written syllabus

General and technical cadres · 235 pages

Compulsory subjects and post-related subjects for professional and technical cadres. Confirm the applicable subject code in the recruitment notice.

Published by BPSC. Collected 2026-11-14. Confirm the edition and subject against your recruitment notice before studying.

Text below is extracted for search and may contain mistakes. Use the original PDF to check marks, formulas and Bangla spelling.

BanglaEnglishBangladesh affairsInternational affairsCivil engineeringElectrical engineeringMechanical engineeringComputer science

Read the document

Page 210 of 235

Searchable text (unverified)
SYLLABUS FOR BCS (WRITTEN) EXAMINATION     
       
210/235 
 
of an enhancement MOSFET, biasing discrete and integrated MOS amplifier circuits, single -stage 
MOS amplifiers, MOSFET as a switch, CMOS inverter. 
 Single-stage and cascode amplifier s, frequency response of differential amplifiers. Operational 
amplifiers (Op -Amp): Non -inverting and inverting amplifiers, inverting integrators, differentiator, 
weighted summer and other applications of Op -Amp circuits. Negative feedback: properties, basi c 
topologies, feedback amplifiers with different topologies, stability, frequency compensation. 
 Basic logic functions, Boolean algebra, combinational logic design, minimization of combinational 
logic. Sequential circuits: different types of latches, flip -flops and their design using ASM approach, 
timing analysis and power optimization of sequential circuits. Modular sequential logic circuit design: 
Shift registers, counters and their applications. 
 
 BJT, MOSFET, SCR, IGBT, BTO, TRIAC, UJT and DIAC. Rectifi ers: Uncontrolled and controlled 
single phase and three phase. Regulated power supplies: Linear -series and shunt, switching buck, buck 
boost, boost and Cuk regulators. AC voltage controllers: single and three phase, Choppers. CD motor 
control, single phase  cycloconverter. Inverters: Single phase  and three phase voltage and current 
source, AC motor control. Stepper motor control, Resonance inverters, Pulse width modulation control 
of static converters. 
 
ELECTRICAL ENGINEERING 
Part-II 
Marks-100 
1. Power Systems: 
 Network representation: Single line and reactance diagram of power system and per unit. Line 
representation: Equivalent circuit of short, medium and long lines. Load flow: Gauss -Siedel and 
Newton Raphson Methods. Power flow control: Tap changing trans former, phase shifting, booster and 
regulation transformer and shunt capacitor. Fault analysis: Short circuit current and reactance of a 
synchronous machine. Symmetrical fault calculation methods: Symmetrical components, sequence 
networks and unsymmetrical fault calculation. Protection: Introduction to relays, differential protection 
and distance protection Introduction to circuit breakers, Typical layout of a substation. Load curves: 
Demand factor, diversity factor, load duration curves, energy load curve,  load factor, capacity factor 
and plant factor. 
  
 Transmission lines cables: Overhead and underground. Stability: swing equation, power angle 
equation, equal area criterion, multi -machine system, step by step solution of swing equation. Factors 
affecting stability, Reactive power compensation. Fleible ac transmission system (FACTS). High 
voltage de transmission system. Power quality: harmonics, sag and swell. 
  
 Power plants: General layout and principles, steam turbine, gas turbine, gas turbine, combined sycle 
gas turbine, hydro and nuclear. Power plant instrumentation. Selection of location: Technical, 
economical and environmental factors. Load forecasting. Generation scheduling: Deterministic and 
probabilistic. Electricity tariff: formulation and types. 
 
2. Telecommunication Systems: 
 Communication systems: Basic principles, fundamental elements, system limitations, message source, 
bandwidth requirements, transmission media types, bandwidth and transmission capacity. Noise: 
Source, characteristics of various types of noise and signal to noise ratio. Information theory: Measure 
of information, source encoding, error free communication over a noisy channel, channel capacity of a 
continuous system and channel capacity of a discrete memory less syst em. Communication Systems: 
Analog and digital. continuous wave modulation: Transmission types, base -band transmission, carrier 
transmission; Amplitude modulation: Introduction, double side band, single side band, vestigial side